1 composite transistors xp06212 (xp6212) silicon npn epitaxial planer transistor for switching/digital circuits features two elements incorporated into one package. (transistors with built-in resistor) reduction of the mounting area and assembly cost by one half. basic part number of element unr1212(un1212) 2 elements absolute maximum ratings (ta=25?c) unit: mm marking symbol: 8v internal connection parameter symbol ratings unit collector to base voltage v cbo 50 v collector to emitter voltage v ceo 50 v collector current i c 100 ma total power dissipation p t 150 mw junction temperature t j 150 ?c storage temperature t stg ?5 to +150 ?c rating of element overall 1 : emitter (tr1) 4 : collector (tr2) 2 : emitter (tr2) 5 : base (tr1) 3 : base (tr2) 6 : collector (tr1) eiaj : sc?8 s?ini type package (6?in) 2.1 0.1 0.2 0.05 0.65 0.65 2.0 0.1 0.9 0.1 0 to 0.1 1.25 0.1 0.425 0.425 1 2 3 6 5 4 0.2 0.1 0.7 0.1 0.2 0.12 +0.05 ?.02 1 tr2 tr1 2 34 5 6 electrical characteristics (ta=25?c) parameter symbol conditions min typ max unit collector to base voltage v cbo i c = 10 a, i e = 0 50 v collector to emitter voltage v ceo i c = 2ma, i b = 0 50 v collector cutoff current i cbo v cb = 50v, i e = 0 0.1 a i ceo v ce = 50v, i b = 0 0.5 a emitter cutoff current i ebo v eb = 6v, i c = 0 0.2 ma forward current transfer ratio h fe v ce = 10v, i c = 5ma 60 forward current transfer h fe ratio h fe (small/large) *1 v ce = 10v, i c = 5ma 0.5 0.99 collector to emitter saturation voltage v ce(sat) i c = 10ma, i b = 0.3ma 0.25 v output voltage high level v oh v cc = 5v, v b = 0.5v, r l = 1k ? 4.9 v output voltage low level v ol v cc = 5v, v b = 2.5v, r l = 1k ? 0.2 v transition frequency f t v cb = 10v, i e = ?ma, f = 200mhz 150 mhz input resistance r 1 ?0% 22 +30% k ? resistance ratio r 1 /r 2 0.8 1.0 1.2 *1 ratio between 2 elements note.) the part number in the parenthesis shows conventional part number.
2 composite transistors xp06212 p t ?ta i c ?v ce v ce(sat) ?i c h fe ?i c c ob ?v cb i o ?v in v in ?i o 0 50 100 150 200 250 02040 80 60 140 120 100 160 ambient temperature ta ( ? c ) total power dissipation p t ( mw ) 0 012 210 48 6 40 120 80 160 140 100 60 20 collector to emitter voltage v ce ( v ) collector current i c ( ma ) ta=25 ? c i b =1.0ma 0.1ma 0.2ma 0.3ma 0.4ma 0.5ma 0.6ma 0.7ma 0.9ma 0.8ma 0.01 0.03 0.1 0.3 0.1 0.3 1 3 10 30 100 1 3 10 30 100 collector current i c ( ma ) collector to emitter saturation voltage v ce(sat) ( v ) i c /i b =10 ta=75 ? c 25 ? c 25 ? c 0 13 100 200 300 400 10 30 100 300 1000 forward current transfer ratio h fe collector current i c ( ma ) v ce =10v ta=75 ? c 25 ? c 25 ? c 0 0.1 0.3 6 5 4 3 2 1 1 3 10 30 100 collector output capacitance c ob ( pf ) collector to base voltage v cb ( v ) f=1mhz i e =0 ta=25 ? c 1 3 0.4 10 30 100 300 1000 3000 10000 1.4 1.2 1.0 0.8 0.6 output current i o ( a ) input voltage v in ( v ) v o =5v ta=25 ? c 0.01 0.03 0.1 0.3 0.1 0.3 1 3 10 30 100 1 3 10 30 100 input voltage v in ( v ) output current i o ( ma ) v o =0.2v ta=25 ? c
please read the following notes before using the datasheets a. these materials are intended as a reference to assist customers with the selection of panasonic semiconductor products best suited to their applications. due to modification or other reasons, any information contained in this material, such as available product types, technical data, and so on, is subject to change without notice. customers are advised to contact our semiconductor sales office and obtain the latest information before starting precise technical research and/or purchasing activities. b. panasonic is endeavoring to continually improve the quality and reliability of these materials but there is always the possibility that further rectifications will be required in the future. therefore, panasonic will not assume any liability for any damages arising from any errors etc. that may ap- pear in this material. c. these materials are solely intended for a customer's individual use. therefore, without the prior written approval of panasonic, any other use such as reproducing, selling, or distributing this material to a third party, via the internet or in any other way, is prohibited. request for your special attention and precautions in using the technical information and semiconductors described in this material (1) an export permit needs to be obtained from the competent authorities of the japanese govern- ment if any of the products or technologies described in this material and controlled under the "foreign exchange and foreign trade law" is to be exported or taken out of japan. (2) the technical information described in this material is limited to showing representative character- istics and applied circuit examples of the products. it does not constitute the warranting of industrial property, the granting of relative rights, or the granting of any license. (3) the products described in this material are intended to be used for standard applications or gen- eral electronic equipment (such as office equipment, communications equipment, measuring in- struments and household appliances). consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. ? any applications other than the standard applications intended. (4) the products and product specifications described in this material are subject to change without notice for reasons of modification and/or improvement. at the final stage of your design, purchas- ing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifications satisfy your requirements. (5) when designing your equipment, comply with the guaranteed values, in particular those of maxi- mum rating, the range of operating power supply voltage and heat radiation characteristics. other- wise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, redundant design is recommended, so that such equipment may not violate relevant laws or regulations because of the function of our products. (6) when using products for which dry packing is required, observe the conditions (including shelf life and after-unpacking standby time) agreed upon when specification sheets are individually exchanged. (7) no part of this material may be reprinted or reproduced by any means without written permission from our company. 2001 mar
|
